Red Nebula Studios

Fantasy art, costumes, crafts,
and creative endeavors.

Red Dragon Trophy Wall Mount

Red Dragon Trophy Wall Mount by Sarrah Wilkinson - My red dragon trophy wall mount, crafted from one of my lizard masks with additional hand-sculpted details on the neck and hand painted.

So, let's say you really like my lizard mask, but have no real interest in dressing as a lizardperson or a dragon. Here's something else I thought of to do with it!

While I may have dragon wall mounts like this available in my shop from time to time (check if there are any store links at the bottom of this page, or you can peruse the Red Nebula Studios Etsy shop!), I'm giving a detailed series of photos below showing how I made this one so you can choose if you'd like to make one, too!

Build process for my red dragon trophy, starting with one of my lizard masks, a set of horns, eyes, and a wooden interior support.

I started with one of my lizard mask casts, just a close-mouthed cast right out of the mold. (I no longer have this version of the mask available, but I have a new updated lizardman mask available from the Lizardman Resin Mask Kit - Order Form right here on this site. I also used a set of my 8" horns and slitted glass eyes (also available on that same order form). The wood block will form the basis for the neck, as you'll see in a moment.

Build process for my red dragon trophy - Eye attached and additional sculpting in epoxy. Build process for my red dragon trophy - Nostril filled with epoxy.

First, I cut out the mask's eye holes and glued in the glass eyes, using FreeForm Air* epoxy putty to fill in the gaps around them (and also putting some around the backs of the eyes to make sure they stayed in place). I used some additional epoxy putty to detail the normally open vision area beneath the eyes, and to make a nice deep nostril hole.

*I'll reference using epoxy putty a number of times throughout this article - in all cases, I'm using a marvelous, lightweight variety known as FreeForm Air, available from Smooth-on. Because of its lightweight properties, the entire sculpture - even including the wooden base - weighs in at about 5 lbs total.

Build process for my red dragon trophy - Wooden neck support. Build process for my red dragon trophy - Wooden neck support.

I used hot glue to attach the wooden support to the inside of the mask at the appropriate angle, and then (not pictured) used epoxy putty to reinforce the connection point.

Build process for my red dragon trophy - Cardboard neck build in progress. Build process for my red dragon trophy - Cardboard neck build in progress and horns attached. Build process for my red dragon trophy - Neck being covered with a base coat of FreeForm Air epoxy putty.

The bulk of the neck was built with cardboard and hot glue, getting the basic shape first and then filling in the gaps to get a nice curved shape. After that, I covered the entire thing with a layer of epoxy putty to give it a uniform strength and a good structure to start building details over.

Build process for my red dragon trophy - Details being added with FreeForm Air epoxy putty. Build process for my red dragon trophy - Details being added with FreeForm Air epoxy putty.
Build process for my red dragon trophy - Details being added with FreeForm Air epoxy putty. Build process for my red dragon trophy - Details being added with FreeForm Air epoxy putty.

Doing detail work with FreeForm Air is interesting, because it's not really meant to be a sculpting material! It's quite soft, so it has to be carefully applied and cannot be bumped before it starts curing - kind of like sculpting with bread dough. However, it CAN be done. It can even be textured to a degree, by waiting for it to partially cure and then using a wet texture stamp on the surface.

FreeForm can also be smoothed out with water and a soft paintbrush, so I used that technique to get the details of each and every hand-sculpted scale to look just right and match the scales and other details of the original mask.

Build process for my red dragon trophy - Primed in grey and ready to paint. Build process for my red dragon trophy - Primed in grey and ready to paint. Build process for my red dragon trophy - Base colors added with spray paint.

Once all the sculpting work was completed and cured, I masked off the eyes and the entire piece was primed in grey. After that, I masked off various areas at a time and did the base paint coats with a few different colors of spray paint.

The final red dragon trophy wall mount, with detail painting done and attached to base. The final red dragon trophy wall mount, with detail painting done and attached to base. The final red dragon trophy wall mount, with detail painting done and attached to base. Photo includes a ruler to show size.

And finally, the remaining painted details were done with washes and drybrushing using acrylic paints. The entire mask was then sealed with spray acrylic for a satin shine and mounted to its stained wooden plaque. (And yup, I stained the plaque myself too. :) )

Available For Sale:

This is a red dragon trophy wall mount I crafted using one of my lizard masks for the face, and hand sculpted additional neck details. It is hand painted and attached to a stained pine base with mounts to hang it from a wall.Red Dragon Trophy Wall Mount - via etsy.com

© 2016 Lizard mask base, additional sculpting, and painting by Sarrah Wilkinson

Completion date: 2/20/2016 - Page last updated: 3/9/2017

Keywords: red dragon trophy, dragon sculpture, wall mounted dragon, lizard mask, dragon head, dragon bust, painted, finished, detailed

Categories: Artwork, Fantasy, Just Dragons!, Sculptures and Traditional Artwork